How to unblock a sink: plunger, trap and drain steps
Most sink blockages sit in the trap or the first metre of pipe. Here's how to clear one with a plunger, a trap clean-out or a drain snake, safely.
The short answer
Almost every blocked sink in a home is blocked in one of two places: inside the trap — the U-shaped or bottle-shaped fitting directly under the plughole — or in the first metre of waste pipe beyond it. Fat, food scraps, hair, soap and toothpaste set hard on the inside of the pipe and narrow it until water stops running away.
The order that works most often is:
- Plunge first, with the overflow sealed.
- If that fails, put a bucket under the trap and clean it out by hand.
- If water still stands, rod the pipe with a manual drain snake.
- Use a chemical cleaner last, and never straight after plunging.
Most blockages of this kind clear well inside an hour with a plunger, a bucket and a couple of old towels. You do not need to take the sink off the wall or dismantle the whole waste run.
- Kitchen sink
- Congealed cooking fat, food scraps, coffee grounds and the silt that collects behind them.
- Bathroom basin
- Hair, soap, shaving foam and toothpaste, which set into a putty-like plug around the plughole and in the trap.
- Utility or downstairs cloakroom sink
- Lint and detergent residue from hand-washing, plus soil from gardening and grit from decorating.
- Sink with a washing machine or dishwasher on the same waste
- Lint and food pushed back up the appliance hose, or a blocked spigot where that hose joins the waste pipe.
What you need before you start
- Rubber cup plunger
- A plain cup plunger, not the flanged type made for toilets. A wide, soft cup seals best on a flat sink base.
- Bucket and washing-up bowl
- One that fits under the trap, plus a second bowl to catch the trap contents.
- Old towels and a cloth
- For the cupboard floor, and a wet cloth to seal the overflow while you plunge.
- Water pump pliers or adjustable spanner
- Only for stubborn trap nuts. Most plastic traps undo by hand.
- Manual drain snake
- A hand snake a few metres long is plenty for a sink branch. A drain wire or bent coat hanger will do for a short trap arm.
- Rubber gloves and eye protection
- Waste water carries bacteria, and any chemical cleaner you have already used is caustic.
- Washing-up liquid and a kettle
- Hot, not boiling, water for flushing fat through the pipe.
- Torch
- To look into the pipe stub and to check the unions for leaks afterwards.
Before you take anything apart, look at what is under the sink. A bottle trap is a cylinder with a removable base that can be emptied without undoing the pipework. A P-trap or tubular trap has two hand-tight union nuts with a rubber washer at each — these are the ones that leak if you cross-thread them. A telescopic trap adjusts in length and can hide an extra seal that drops out when you unscrew it.
Also check whether a washing machine, dishwasher or water softener drains into the same waste pipe. If one does, its hose usually joins above the trap through a spigot, and a blockage there looks exactly like a blocked sink.
Work out where the blockage is
A few minutes of diagnosis saves an hour of pointless work. Run the hot tap and watch what happens.
- Just this one sink, water standing in the bowl. The blockage is almost certainly in the trap or the short arm of pipe behind it, and it is yours to fix.
- The sink drains slowly, but the washing machine or dishwasher backs up into it. The shared waste pipe below the appliance connection is partly blocked, so water takes the easiest route back up.
- Water comes up in the bath, shower tray or another basin when you run this tap. The blockage is downstream, in the shared branch or the stack. Stop and call a drainage company.
- The sink empties but gurgles afterwards. Air is being sucked through the trap because the pipe beyond is restricted. It usually means a build-up rather than a complete block.
- The trap is clear and water still will not move. The blockage is in the pipe run or the gully outside, and a hand snake may not reach it.
Step by step: clearing a blocked sink
-
01 /
Bail out the standing water
Scoop the water out with a mug into a bucket and stop when there is just enough left to cover the rubber cup of the plunger. Do not tip dirty standing water down another sink — you will only pass the problem on.
-
02 /
Try hot water and washing-up liquid
For a sink that is draining slowly rather than completely blocked, pour a kettle of hot — not boiling — water into a jug, add a good squirt of washing-up liquid and pour it slowly into the plughole. Leave it five to ten minutes, then run the hot tap and watch how the water leaves. This shifts light fat and soap film but will not clear a solid plug.
-
03 /
Plunge with the overflow sealed
Wet a cloth, wring it out and press it firmly over the overflow slot on the basin or sink. This is the step most people skip, and without it the plunger just pushes water out of the overflow. Make sure the cup is covered by water, set it over the plughole and give 10 to 15 short, sharp pushes and pulls, keeping the seal. Break the seal and see whether the water drops.
-
04 /
Block a second bowl or an appliance hose
On a double sink, hold a wet cloth or the second plunger over the other plughole so the pressure cannot escape. If a washing machine or dishwasher hose joins the waste above the trap, it will take the pressure instead of the blockage, so plug or clamp it at the spigot where the connection allows.
-
05 /
Put a bucket under the trap and open it
Spread old towels in the cupboard, slide the bucket under the trap and unscrew the union nuts by hand, turning anticlockwise. Keep the bowl directly under the joint as it opens. If a nut is tight, use water pump pliers with light pressure only — plastic nuts crack easily.
-
06 /
Clean the trap and check the pipe stub
Tip the trap contents into the bucket, not down another drain, and rinse the trap under the tap. Shine a torch into the pipe stub going into the wall; food and hair often sit just inside the first bend. Fish it out with a bent piece of wire, and check that the rubber washer is still sitting in its groove.
-
07 /
Rod the pipe if the trap was clear
Feed a manual drain snake through the open trap arm, or down the plughole with the trap removed. Turn the handle clockwise as you push, and stop if you meet solid resistance rather than forcing through it. Wrap a strip of tape round the snake at the point where it first binds so you know how far in the blockage sits.
-
08 /
Reassemble, flush and test
Refit the trap hand-tight only, checking that no washer is pinched. Run hot water for a minute and look at the unions with a torch while it flows. Then fill the bowl to the brim, pull the plug and watch the water leave in one steady swirl. A slight weep at a union needs a quarter turn more, not a wrench.
Plunger technique that actually works
A sink plunger is a plain rubber cup on a handle. The flanged version sold for toilets has a folded skirt shaped to sit inside a toilet outlet, so it seals badly on a flat sink base and makes a poor substitute.
The technique matters as much as the tool:
- Seal every escape route. Overflow first, then a second bowl or an appliance hose.
- Keep the cup under water. Air leaks in if the bowl is nearly empty and the plunger loses its grip.
- Push slowly, pull sharply. The pull is what drags the plug of fat or hair back up into the trap.
- Work in rounds. Ten to fifteen strokes, break the seal, check the water level, then repeat. After four or five rounds with no improvement, move on to the trap.
Cleaning the trap without flooding the cupboard
Under-sink traps hold more water than people expect — often a mugful or more — and the contents smell far worse than the sink suggests. Work in this order:
- Bucket directly under the joint, towels packed round it.
- Undo the lowest nut first so the water runs into the bucket rather than down your arm.
- Keep each washer with its own joint. They are often different sizes, and a swapped washer will leak.
- Scrub the inside of the trap with an old washing-up brush rather than a knife or a wire coat hanger, which scratches the plastic and gives the next blockage something to grip.
- Check the seal on the base of a bottle trap — it is a common source of a slow drip afterwards.
Chemical drain cleaners: the last resort
Most chemical cleaners are caustic soda (sodium hydroxide) or an acid blend, sometimes with bleach. They work by dissolving hair, soap and light fat, which makes them reasonably effective on a slow bathroom basin and useless against a solid plug of food, a build-up of scale or a mechanical obstruction such as a bottle top or a broken plug chain.
They also carry real risks in a domestic sink:
- Caustic soda gives off heat as it dissolves, which can soften older plastic waste pipes and distort rubber seals.
- Acid cleaners attack metal traps, brass waste fittings and enamel if left standing.
- Both are dangerous to skin and eyes and must never be mixed with each other, with bleach, or with a different cleaner already sitting in the trap.
- Some products are unsuitable for septic tanks or for properties with a macerator or pumped waste; the label will say so.
If you decide to use one: read the label, wear gloves and eye protection, open a window, measure the stated dose rather than guessing, keep to the time on the pack, and flush with plenty of cold water afterwards.
Which method for which blockage
| Method | Best used for | Watch out for |
|---|---|---|
| Cup plunger | Soft blockages of fat, soap and hair in the trap and the first metre of pipe | Does nothing if the overflow is not sealed or if the blockage sits well downstream |
| Removing and cleaning the trap | Solid plugs of food, coffee grounds, hair and thick sludge | Messy; cracked or cross-threaded nuts leak afterwards |
| Manual drain snake | Blockages past the trap, in the waste pipe or the branch to the stack | Can scratch plastic if forced, and will not clear a collapsed or root-blocked pipe |
| Hot water and washing-up liquid | Light fat, soap film and routine flushing of a slow sink | Boiling water can soften plastic waste pipes and push-fit seals |
| Wet and dry vacuum | Sucking loose debris and standing water out of the trap and pipe stub | Only reaches shallow blockages, and a wet filter sprays dirty water |
| Chemical cleaner | Hair, soap scum and light fat in a basin that drains slowly | Slow to act, can damage seals, and must never be combined with plunging |
When to stop and call a drainage company
Some blockages are genuinely not a DIY job. Stop and ring a professional if:
- Water appears in another fixture — a bath, shower tray, basin or outside gully — when you run this tap.
- The trap and the visible pipe are clear, but the sink still fills.
- The same sink blocks again within a few weeks. That points to scale, a sag in the pipe, a poor fall or roots outside, none of which a hand snake will fix.
- There is a macerator or pumped waste unit under the sink. These need an engineer, not a rod.
- You rent the property. Waste pipes and drains are normally the landlord's responsibility, and a DIY repair that goes wrong can affect your deposit.
- The water is foul and dark, or there is a smell of sewage. That is a drain problem, not a sink problem.
Keeping the sink clear
Once the water is running away, a few habits stop the same blockage coming back:
- Fit a mesh strainer in the plughole and empty it into the bin, not back down the sink.
- Pour cooled fat and oil into a jar or the food waste caddy. Wipe greasy pans with kitchen roll before washing them.
- Once a week, fill the bowl with hot water and a squirt of washing-up liquid and let it go in one surge. The rush of water clears light film from the pipe walls.
- In a basin, a hair trap over the plughole catches most of what would otherwise set solid in the trap.
- Bin coffee grounds, tea leaves, rice and flour. They swell or set into a paste that water cannot shift.
- Run the cold tap for a few seconds after a hot flush or a chemical treatment so the trap refills and the seal against drain smells is restored.
Common questions
Why does my sink drain slowly rather than blocking completely?
A slow drain usually means the pipe has narrowed rather than closed. Fat, soap and hair build up in layers on the pipe wall and leave a small channel in the middle. Cleaning the trap and flushing with hot soapy water often restores most of the flow, but if the slowness returns within a few weeks the pipe itself needs rodding.
Can I use a toilet plunger on a sink?
It will shift some water but it seals badly. The folded flange on a toilet plunger is shaped to sit inside a toilet outlet; on a flat sink base it collapses and lets water past. A plain cup plunger gives a far better seal and is what the technique above assumes.
Do bicarbonate of soda and vinegar clear a blocked sink?
Rarely on their own. The fizz is carbon dioxide escaping and there is very little force behind it. The mixture can loosen light soap film, but a solid plug of fat or hair needs the mechanical pull of a plunger or a snake. If you try it, follow with hot water and a plunge.
Is boiling water safe to pour down a sink?
It depends on the pipework. A ceramic sink with a metal waste can take a kettle of boiling water poured slowly into the plughole. Plastic waste pipes and push-fit seals can soften or distort, so use the hottest water from the tap instead, or let the kettle stand for a couple of minutes first.
What does gurgling after the sink empties mean?
It means air is being drawn through the trap because water is not flowing freely beyond it, usually a partial blockage or a build-up in the branch pipe. Treat it as an early warning: clear it now with hot water and a plunge and you are much less likely to face a full blockage later.


