Skip to content
Design Smart

Room Notes

How to Stop Your Dishwasher Smelling: A Step-by-Step Fix

A clean filter, a hot cycle and a wiped seal will shift most dishwasher smells. Here's the order to do it in, and what to check if it comes back.

Cleaning gloves, spray bottles and sponges on white

The short answer

Almost every smelly dishwasher is a cleaning problem, not a broken machine. Food scraps, grease and the film they leave behind collect in the filter, the sump under the bottom basket, the door seal and the spray arms. Warm and permanently damp, that debris grows a biofilm — the slimy layer behind the sour, drainside whiff you get when you open the door.

The fix is to strip out the debris, then run a hot empty programme to flush the pump and pipework. Most machines come back fresh after an hour of hands-on work. Only if the smell returns within a handful of washes do you need to look at the drain hose, the plumbing connection or your salt and rinse aid settings.

What you need before you start

Nothing here requires disconnecting the water supply. Gather these first so you're not hunting for them with wet hands:

  • Rubber gloves and a torch — the sump is dark and you'll be reaching into it
  • An old toothbrush, plus a cocktail stick or pipe cleaner for the spray arm holes
  • A bowl of hot water with a little washing-up liquid, and two clean cloths
  • A dishwasher cleaner, or citric acid and bicarbonate of soda for a homemade version
  • White vinegar if you live in a hard water area
  • Kitchen roll or a sponge for soaking up standing water

Step by step: the deep clean

  1. 01 /

    Empty the machine and remove both baskets

    Take out every dish, the cutlery basket and the upper basket if it lifts out easily. You need a clear view of the base and the floor of the tub.

  2. 02 /

    Lift out the filter assembly

    Most filters are a cylindrical mesh unit that twists anticlockwise and lifts out, sitting over a flat fine filter or filter plate. Take both parts out and separate them.

  3. 03 /

    Scrub the filter under a hot tap

    Use the toothbrush and a little washing-up liquid to work around the mesh, the inner cone and the rim where grease collects. Rinse until the water runs clear and you can see daylight through the mesh.

  4. 04 /

    Soak up the water in the sump

    Press a sponge or kitchen roll into the recess the filter came out of and remove any standing water. Wipe the walls of the recess and the ledge the filter seats on, then check for trapped food, broken glass or a stray piece of cutlery.

  5. 05 /

    Clean the door seal all the way round

    Run a cloth dipped in hot soapy water along the whole rubber gasket, including the bottom edge you can't see when the door is shut. Use the toothbrush in the folds, then dry it with a second cloth.

  6. 06 /

    Clear the spray arm holes

    Unclip or unscrew the spray arms if your model allows it, rinse them through, and poke out any blocked holes with a cocktail stick. Hold them up to the light to check the jets are clear.

  7. 07 /

    Wipe the door interior and detergent drawer

    Wipe the inside of the door, the edges, the detergent and rinse aid drawer and the salt cap area. Grease film builds up here quietly and is a common source of a stale smell.

  8. 08 /

    Run the hottest empty programme

    Put the cleaning agent in the base of the empty machine rather than the detergent drawer, and run the longest, hottest programme — usually the intensive one, around 65–70°C. Don't add dishes.

  9. 09 /

    Dry it out and leave the door ajar

    When the programme ends, wipe any water left in the sump and around the seal, then leave the door slightly open so air can circulate.

The filter is where most smells start

The filter catches everything that comes off your plates, and it sits in warm, wet, dark conditions for hours at a time — ideal for the bacteria that produce that drainside smell. Rinsing it under the tap without scrubbing isn't enough: you need to shift the greasy film from the mesh, not just the visible crumbs.

Some manufacturers say the filter can go through a dishwasher cycle, but washing it by hand under a hot tap with a brush is far more reliable. The machine can't clean the part that's doing the cleaning.

Check the filter seat as well as the filter itself. If the assembly doesn't click back flat and tight, water bypasses the mesh and food heads straight for the pump, where it settles and rots.

The door seal, hinges and detergent drawer

The bottom door seal is the most overlooked part of the machine. Water sits in its folds, food particles lodge there, and black mould blooms in the crevices. Wipe the whole gasket with hot soapy water, get into the folds with a toothbrush, and dry it afterwards — a damp seal left shut is the perfect incubator.

While you're there, wipe around the hinges, the inside of the door and the detergent drawer recess. If you use tablets and never touch the drawer, it can still hold a residue of old powder or rinse aid that turns stale. The salt cap area deserves a wipe too, especially if you've ever overfilled the reservoir.

Spray arms, sump and the parts you can't see

Blocked spray arm jets don't just give you dirty dishes — the trapped food in the arms sours between washes. Rinse the arms through and clear every hole. On models where the arms don't detach, hold a bowl of hot soapy water under them and let it run through the jets, then poke out stubborn bits with a cocktail stick.

In the sump, work around the filter housing with a cloth and check the cover plate or non-return flap if your model has one. This is also where you'll spot the real warning sign: water that won't drain away or keeps reappearing after you've sponged it out.

Running the hot maintenance programme

Once the machine is clean, the hot programme does two jobs: it flushes grease out of the pump and pipework, and it kills off much of what's left on the internal surfaces. Put the cleaner or a couple of tablespoons of citric acid in the base of the empty tub, not in the detergent drawer, and use the hottest, longest programme your machine has.

If your household normally runs only eco or 30-minute cycles, this is the step that matters most. Short, cool programmes use less water and lower temperatures, so grease gradually coats the inside of the machine instead of being carried away. Running a hot programme once a month makes a noticeable difference.

If the smell comes back: the drain hose and plumbing

A dishwasher drains into either a standpipe or a spigot on the sink waste trap. Either way, the hose must loop up high — roughly to the height of the worktop — before it connects. If it sags, dirty water from the sink runs back down into the machine and sits there, and no amount of filter scrubbing will cure it.

Check three things: that the hose rises in a loop before it meets the connection, that the spigot on the waste trap isn't clogged with fat, and that the knock-out plug in a new spigot was actually removed. A blocked spigot shows up as a gurgle and a whiff of drains when you empty the sink.

What the smell is telling you

Match the smell to the most likely cause before you start pulling things apart.
What you noticeLikely causeFirst thing to try
Sour or musty, worst when you open the doorBiofilm on the filter, sump and sealScrub the filter, sponge out the sump, wipe the seal, run a hot empty programme
Rotten eggs or drainsideFood debris in the filter housing, or standing water in the baseSoak up the water, reseat the filter properly, check the drain hose loop
Fishy or stale, dishes still feel greasyGrease film on the tub walls and spray armsWipe the walls and door with hot soapy water, clear the spray jets, run the hottest programme
Drains smell when the sink is emptiedClogged waste spigot, or a hose that sags instead of looping upClean the spigot, raise the hose into a high loop
Chemical or plastickyOverdosed detergent or rinse aid, or a brand new machineRun an empty hot rinse, reduce the dose to the recommended level
Musty after every wash, everything still wetRinse aid empty, or poor dryingRefill the rinse aid, leave the door ajar after each programme

Common mistakes that keep the smell coming back

  • Rinsing plates to perfection but never cleaning the filter. Grease still coats the mesh even when there's no visible food.
  • Refitting the filter wet and half-seated. It has to click flat; if it doesn't, debris goes straight into the pump.
  • Using only quick, cool programmes. Grease never gets flushed out. Add a hot cycle monthly.
  • Blocking the spray arms with tall items. Water can't reach the filter to wash the debris down.
  • Shutting the door straight after a cycle. Trapped warmth and moisture encourage mould on any residue.
  • Splashing white vinegar in with every wash. Occasional use is fine; repeated acid exposure can harden rubber seals over time.
  • Ignoring the salt reservoir in hard water areas. Limescale gives grime something to cling to, and scale plus grease is a stubborn combination.

Keeping it fresh between deep cleans

Once you've done the deep clean, a few small habits keep the smell away:

  • Rinse the filter under the hot tap every few weeks and reseat it firmly
  • Run a hot empty programme with a cleaner once a month, or every six weeks in soft water areas
  • Keep rinse aid topped up so dishes and the tub dry properly
  • Check the salt level monthly if you're in a hard water area
  • Leave the door ajar between washes, and wipe the seal dry if you've time
  • Run a hot programme straight after a fish dinner or a very greasy roasting tin
  • Don't leave dirty dishes sitting in a closed machine overnight — scrape and run, or leave the door open

When the smell isn't dirt

A few causes sit beyond a scrubbing brush. Water that stands in the base after the machine has finished points to a blocked drain path or a failing pump. A machine that drains slowly and gurgles is telling you the same thing.

In rare cases the smell comes from something trapped where you can't reach — a spill that has soaked into the base insulation, or a rodent in the casing. If you've cleaned everything thoroughly, fixed the hose loop and run several hot cycles, and a genuinely foul smell persists, it's worth paying an appliance engineer to look rather than pouring more chemicals into it. Persistent damp patches around the machine should be dealt with at the same time, since they're a separate problem that smells like a dishwasher fault.

Frequently asked questions

Can I use white vinegar to clean a dishwasher?

Yes, as an occasional descaler: put a mug of white vinegar in the bottom basket and run a hot empty programme. Don't add it to every wash, because repeated acid exposure can harden rubber seals over time.

How often should I clean the dishwasher filter?

Rinse it under a hot tap once a month, and scrub it properly whenever it feels slimy. Households that cook a lot of fish, eggs or dairy may need to do it fortnightly.

Will a smelly dishwasher make my dishes smell?

Yes. Biofilm in the filter and sump leaves a film on glassware, cutlery and especially plastic items and mugs. Cleaning the machine and running a hot cycle usually clears it.

Is a smelly dishwasher a sign it needs replacing?

Rarely. Smells almost always come from debris in the filter, sump, seal or drain hose. Only a persistent smell accompanied by standing water in the base suggests a blockage or pump fault worth an engineer's visit.

Can I use bleach or drain cleaner in the dishwasher?

No. Bleach hardens rubber seals and can corrode stainless steel parts, while drain cleaner is formulated for waste pipes and can damage the pump. Use a dishwasher cleaner or citric acid instead.

Why does my dishwasher only smell after it's been shut for a while?

Warm, damp air trapped behind a closed door encourages mould and bacteria on any residue left inside. Leaving the door ajar after each programme and drying the seal makes a real difference.

Search