How to Fix a Dripping Tap: Washer and Cartridge Repair
Fix a dripping tap yourself: find out which tap you have, isolate the water, swap the washer or ceramic cartridge and test the repair.
The short answer
A dripping tap nearly always comes down to one worn part. On a traditional tap with a head that winds down, it's the rubber washer (or the jumper it sits on) that has perished. On a quarter-turn tap, it's the ceramic cartridge inside. The shape of the job is the same either way: isolate the water, take the tap apart, swap the part, rebuild it and test.
A washer tap is usually a half-hour job with a spanner and a screwdriver. Cartridge taps can be quicker still, because there's no stiff nut to fight with — but the cartridge has to match exactly.
Don't put it off. A tap that drips constantly wastes water, stains the basin and, if you're on a meter, adds to every bill. A drip from the spout is also one of the cheapest plumbing faults to put right.
Work out which tap you have before you buy anything
Look at how the head turns. A head that moves a quarter turn and stops with a positive click is a ceramic cartridge tap. A head that turns two or three full turns and winds down is a traditional washer (compression) tap. Mixer taps can be either: a single lever that lifts and swivels is almost always ceramic, while a mixer with two separate cross-heads is usually two washer valves side by side.
It's worth knowing which you've got before you start, because the parts and the technique are different.
| Tap type | Traditional washer tap | Quarter-turn ceramic tap | Single-lever mixer |
|---|---|---|---|
| How it feels | Two or three full turns; the head winds down and stops | A short quarter turn with a firm click at the end | A lever that lifts for flow and swivels for temperature |
| Usual cause of a drip | A perished rubber washer, or a worn jumper underneath it | Worn ceramic discs, or a damaged O-ring inside the cartridge | A worn cartridge, or grit and limescale trapped between the discs |
| What you replace | The washer, and the jumper if worn; reseat the seat if it is pitted | The complete cartridge — there is no separate washer to change | The cartridge under the lever; a two-handle mixer has one valve each side |
| How you get inside | Undo the screw under the hot/cold cap, lift off the handle, undo the headgear nut | Undo the grub screw at the back of the handle, then lift out the cartridge | Prise off the lever, unscrew the retaining collar, lift out the cartridge |
What to have ready
- An adjustable spanner, plus a basin wrench if the tap is on a basin and the nut is hidden behind the pedestal
- A flat-blade screwdriver and a cross-head screwdriver
- A small Allen (hex) key for the grub screws on lever handles
- Replacement washers and O-rings, or the correct cartridge
- Silicone plumber's grease
- A cloth, a small bowl or bucket, and a torch
- A plug in the basin waste, so screws can't vanish down the drain
In the UK, replacement parts for taps that supply drinking water should be suitable for potable water — look for the WRAS approval mark on the packaging. It matters most on a kitchen tap, where the water goes straight into a glass.
Turn the water off — and prove it's off
-
01 /
Close the isolating valve under the tap
Most basins and sinks have a small slotted screw valve on each supply pipe, turned with a flat screwdriver. Turn it clockwise until it stops. Kitchen sinks sometimes have none at all.
-
02 /
If there's no isolating valve, close the main stopcock
Usually under the kitchen sink, in a downstairs cupboard or under the floor near where the supply enters. Turn it clockwise. On a gravity system with a cold tank in the loft, you also need to stop the hot supply — close the gate valve on the pipe leaving the cylinder, or bung the outlet in the loft tank.
-
03 /
Open the tap and let it run dry
Open both hot and cold on a mixer. Once the flow stops, close them again. This releases the pressure and shows whether the valve is actually holding.
-
04 /
Check again a minute later
Reopen the tap. If water still trickles out, the valve is passing and you must not dismantle anything yet.
Take the tap apart
-
01 /
Protect the finish
Wrap the spanner jaws in cloth or use smooth jaws. Chrome scratches easily, and a rounded nut turns a half-hour job into a much longer one.
-
02 /
Remove the handle
Prise off the small hot/cold indicator cap on top with a thin screwdriver and undo the screw underneath. On a lever handle it's usually a grub screw at the back — swivel the lever to find it.
-
03 /
Lift off the shroud
Take off the cover so the headgear nut is exposed. Keep screws and caps in a bowl where you can see them.
-
04 /
Undo the headgear nut
This is the large nut directly under the handle. Hold the tap body steady with your other hand so you don't strain the pipework below the worktop.
-
05 /
Lift out the works
On a washer tap you'll find a brass jumper with the rubber washer underneath, or a washer held on the end of the spindle. On a ceramic tap the cartridge simply lifts out.
Fit the new washer or cartridge
-
01 /
Match the part to the old one
Compare them side by side. A traditional UK pillar tap usually takes a ½ inch washer, but check — old taps are sometimes fitted with whatever was to hand.
-
02 /
Inspect the valve seat
Look down into the tap body where the washer sits. It should be a smooth, even ring. If it's pitted, scored or crusted with limescale, a new washer will drip again within weeks. The seat needs reseating with a reseating tool, or the tap needs replacing.
-
03 /
Fit the washer the right way round
A flat washer sits flat against the seat; a domed or top-hat washer goes with the shape facing up towards the spindle. Smear a little silicone grease on it.
-
04 /
Fit the cartridge the same way it came out
Note which way the locating lugs face before you lift the old one out — a photo saves guesswork. Push the new cartridge in squarely and don't force it.
-
05 /
Replace the O-ring too, if there is one
If the drip was coming from the base of the spout or from under the handle rather than the spout itself, the worn part is an O-ring or gland, not the main washer.
Put it back together and test
-
01 /
Reassemble in reverse order
Cartridge or jumper in, headgear nut on, shroud, handle screw, indicator cap. Start every thread by hand and only nip up with a spanner — overtightening splits brass and distorts the new washer.
-
02 /
Turn the water on slowly
Open the isolating valve a quarter turn, listen, then open it fully. Opening it fast sends a slug of air and debris through and can start a fresh leak.
-
03 /
Run the tap through
Open it fully, then close it. Check the spout for drips, then look under the basin with a torch for weeping around the headgear and the supply connections.
-
04 /
Give it an hour
Dry everything, leave it, and check again. A tiny weep that settles after a few uses is usually fine; a steady drip is not.
When it still drips: the usual culprits
- It drips exactly as before. The washer is the wrong size or fitted upside down, or the seat is pitted. Take it apart and feel the seat.
- It drips from the base of the spout or under the handle. That's an O-ring or gland, not the main valve. The tap needs a seal kit or replacing.
- The head is stiff or won't turn. The headgear is cross-threaded or over-tightened. Undo it, grease the thread and start again by hand.
- The handle won't come off. There's a second screw hidden somewhere, or the grub screw is seized. Don't lever the handle — a little penetrating oil and patience beats a broken fitting.
- Water pours out when you turn it back on. Something isn't seated: usually the cartridge isn't pushed fully home, or the headgear nut is cross-threaded.
- A quarter-turn tap still drips after a new cartridge. Wrong cartridge type, or grit trapped against the new discs. Rinse the housing and check the lugs line up.
What not to do
Also worth knowing: never leave the job half done with the water off and no test; never dismantle a tap while water is still trickling from it; and don't throw the old cartridge or washer away until the new one is fitted and tested. It's your only pattern for matching a replacement if you need to go back for another.
When a new tap is the better answer
If the tap body is cracked, the seat is so pitted that a reseating tool can't clean it up, or the tap is an old design whose parts can't be matched, replacing the tap is usually less frustrating than fighting it. The same goes for a tap where the chrome has gone and the spout swivel weeps — the labour to fit a seal kit is the same as the labour to fit a new tap.
If you rent, ask the landlord or agent to deal with it. Taps are part of the fixtures, and a botched repair becomes your problem rather than theirs.
And if the drip is coming from a pipe joint or from under the floor rather than from the tap itself, stop: that's a different job and may need a plumber.
Keeping drips away
- Turn taps off firmly, not hard. Cranking a washer tap down tight squashes the washer and shortens its life.
- In a hard water area, limescale on the seat is what wears washers out. A scale reducer or softener on the supply pays for itself in tap repairs.
- Wipe the spout and dry around the base now and then — standing water attacks chrome and seals.
- Fix a weep when you first notice it. A slow leak under the handle can rot a worktop or a cabinet base long before it becomes a visible puddle.
Common questions about dripping taps
The water won't stop even with the stopcock closed. What now?
The stopcock itself is probably passing. Try the isolating valve on the tap's own supply pipe instead. If there isn't one, call a plumber to replace the stopcock — don't take the tap apart while water is still running through it.
Can I use a washer from a different-sized tap?
No. An oversized washer won't settle into the seat and an undersized one won't seal the bore. Both will drip again as soon as you turn the water back on.
How long should a tap washer last?
There's no fixed service life. It depends on how often the tap is used and how hard your water is, so washers on a busy kitchen tap in a hard water area wear out far sooner than one on a little-used cloakroom basin.
My mixer drips from the spout when it's off. Which part do I need?
On a single-lever mixer, one ceramic cartridge under the lever controls both hot and cold, so that's the part to change. On a two-handle mixer, each handle has its own valve, so only the side that drips needs attention.
Do I have to drain the whole system?
No. Closing the isolating valve and opening the tap empties only the short length of pipe between the valve and the tap — a cupful at most, which is why a small bowl is enough.


